总变差模型在书画打印宣纸印刷质量预测中的应用

为了建立适用于书画打印宣纸印刷质量的预测模型,本研究测量了14种书画打印宣纸的粗糙度、白度、不透明度、定量、光泽度和针对宣纸特别设定的帘纹深浅以及帘纹疏密度等表面物理参量,并在相同条件下,使用喷墨打印设备输出并测量印品色度值,利用总变差模型构建去除帘纹色差的测定方法,得到与人眼视觉特征相符的色差。运用GRNN广义回归神经网络结合书画打印宣纸表面物理参量与宣纸去帘纹后的色差值,建立预测模型。结果表明,该模型能够在仅测量书画打印宣纸表面物理参量的情况下,便能较为准确地预测书画打印宣纸印刷质量,为书画打印宣纸印刷前的选纸工作提供指导依据。     

输气管道仿真模型校正技术研究进展

为了解决输气管道仿真系统存在计算值与实际值偏差的问题,对解决该问题的模型校正技术展开国内外调研。提出造成仿真计算不精准的三个主要误差来源:输入参数测量误差、缓变参数误差、手工输入误差。最后通过分析国内外仿真模型校正技术研究现状,建议在动态仿真的基础开展输气管道的模型校正技术研究,以避免输气管道系统数据波动带来的误差。     

FDM 3D打印工艺参数对PLA制件力学性能的影响

采用五因素四水平正交试验设计,对16组不同工艺参数(打印层厚、填充密度、打印温度、填充速度、外壳厚度)的FDM 3D打印聚乳酸(PLA)制件力学性能进行了测试和结果分析,确定了影响PLA制件力学性能的主要因素,其中,外壳厚度对制件力学性能影响最为明显,打印温度影响最小,同时分析得到了在打印层厚0.15 mm,填充密度40%,打印温度210℃,填充速度60 mm/s,外壳厚度1.6 mm条件下可获得力学性能最佳的制件。最后对试验数据进行回归分析,拟合得到了FDM打印工艺参数与PLA制件力学性能指标的数学模型;通过对不同打印工艺参数的试样进行试验验证,表明该模型拟合误差小(5%以内),可靠性高,可用来对FDM 3D打印制件的加工提供参考。     

Scalable Clock Synchronization Analysis: A Symmetric Noncooperative Output Feedback Tubes-MPC Approach

In the cyber-physical environment, the clock synchronization algorithm is required to have better expansion for network scale. In this paper, a new measurement model of observability under the equivalent transformation of minimum mean square error (MMSE) is constructed based on basic measurement unit (BMU), which can realize the scaled expansion of MMSE measurement. Based on the state updating equation of absolute clock and the decoupled measurement model of MMSE-like equivalence, which is proposed to calculate the positive definite invariant set by using the theoretical-practical Luenberger observer as the synthetical observer, the local noncooperative optimal control problem is built, and the clock synchronization system driven by the ideal state of local clock can reach the exponential convergence for synchronization performance. Different from the problem of general linear system regulators, the state estimation error and state control error are analyzed in the established affine system based on the set-theory-in-control to achieve the quantification of state deviation caused by noise interference. Based on the BMU for isomorphic state map, the synchronization performance of clock states between multiple sets of representative nodes is evaluated, and the scale of evaluated system can be still expanded. After the synchronization is completed, the state of perturbation system remains in the maximum range of measurement accuracy, and the state of nominal system can be stabilized at the ideal state for local clock and realizes the exponential convergence of the clock synchronization system.      

Innovations and productivity: the shift during the 2008 crisis

This paper investigates how the recent crisis of 2008 changed relations between innovation and firm performance in Western Europe. We apply a structural framework of CDM modelling, which incorporates different stages of the knowledge creation process and takes into account the complex nature of innovations. The study is based on a balanced panel data of 420 listed manufacturing firms from the U.K., Germany and France. All the information is gathered from common sources, thereby reducing subjectivity, a typical problem in the field. We found, the crisis resulted in appreciable changes in the model. The most important evidence is enhancement of the role of firm resources in the post-recession period. We also reveal larger barriers for innovations, increased uncertainty and lower state dependence in R&D engagement, product creation and economic performance. These results could indicate the ‘cleaning effect’ of the crisis, which has worsened the business environment and enhanced competition.     

A review on China's wind power accommodation in the background of “Internet+” strategy

The consumption of fossil fuel has resulted in global warming, environmental pollution, and many other crucial problems. Replacing fossil fuel with renewable energy has become an important issue over the recent decades. As a renewable clean energy, wind power is a relatively well‐developed and promising energy method for current technology development in China. Under the background of growing demand for electricity and enhancing awareness for environmental, the “Internet+ wind power” concept has emerged based on both the wind power's characteristics that renewable and non‐polluting, and the rapid development of the Internet in China. Through querying an amount of literature and information, this paper reveals the resource endowment and policy environment about wind power and energy Internet at first. Then, the PEST‐SWOT strategy analysis model is used to analyze the internalities (strengths and weaknesses) and the externalities (opportunities and threats) of “Internet+ wind power”. According to these results, the paper puts forward some measures (development and utilization, business mode) for wind power accommodation. Then some policy recommendations have been proposed. The government should provide favorable conditions for wind power grid with the “Internet+” technology innovation.     

Simplified partitioning model to simulate high pressure under-expanded jet flows impinging vertical obstacles

Various reduced-order models have been developed to quickly model high pressure underexpanded jets. One example is the two-layer partitioning model which was developed to model underexpanded jets, but it has not been evaluated for high pressure jets with obstacles in the jet flow region. This research describes an improved two-layer partitioning model based on the Abel-Noble equation of state that is applied here to model horizontal jet flows impacting a vertical obstacle with validations against high pressure gas experiments, full CFD simulations and a revised notional nozzle model based on the Abel-Noble equation of state. The improved two-layer partitioning model accurately predicts the gas concentrations on the obstacle for a 15 MPa underexpanded jet while consuming much less computational resources and time compared with the full CFD simulation.     

热轧除鳞系统节能方案

针对热轧除鳞系统普遍存在的能源浪费严重的问题,设计了基于预测模型的变频节能方案,通过板坯位置预测、除鳞时间预测、除鳞水量预测和除鳞泵转速控制,合理利用轧制间歇时间使水泵电机变频降速,模拟计算结果表明,可使除鳞电耗降低23.57%。     

Modelling the cross‐contamination of Listeria monocytogenes in pork during bowl chopping

This study has developed a predictive model for the cross‐contamination of pork by Listeria monocytogenes during bowl chopping. The transfer rates of L. monocytogenes were measured in sixteen chopping scenarios based on practical work. Meanwhile, contaminated bowl chopper was cleaned with either a dry rag (DR), warm water (WW) or 70% ethanol + water (EW), respectively. It was showed that significant differences (P < 0.05) were observed among the three cleaning methods on the reduction of L. monocytogenes, the greatest log reduction being achieved by EW. Moreover, the model introduced by a previous study, predicting cross‐contamination of L. monocytogenes during meat slicing, was improved and validated in this study. Verification results showed that the improved model was acceptable for predicting L. monocytogenes cross‐contamination during pork chopping with coefficients of determination (R² > 0.82), accuracy factors (A_f < 1.44), bias factors (B_f < 1.42), and root mean square error (RMSE < 0.99). Furthermore, the modified model might provide an effective tool for assessing the risk of the cross‐contamination of meat products.